dnawujun 发表于 2011-3-25 15:05

发个好东西给大家分享，信的就下

好东西哦~~~，不下的别后悔

y1949b 发表于 2011-3-25 15:23

dnawujun 兄厉害！
要是有有一直期待的MotorSolve的d版本能出来就好了。。。。。。

20041199 发表于 2011-3-25 17:27

楼主，我顶你个肺啊，实在是好东西

zxczcr 发表于 2011-3-25 17:50

谢谢分享。

hscqu 发表于 2011-3-25 17:53

本帖最后由 hscqu 于 2011-3-25 17:54 编辑

我当然信你，果然是好东西，请大家{:1_431:}{:1_431:} {:1_431:} 就行了，别太张扬了喔。

另请确认一下win32是两个文件，而win64是一个文件？

owennnn 发表于 2011-3-25 18:27

explain to us why only one file in folder win64, not whether it is a mistake?

20041199 发表于 2011-3-25 20:18

回复 1# dnawujun

额滴神啊，这都能破解，楼主你太强大了，嫁给我吧{:1_432:}

tjin 发表于 2011-3-25 20:45

flux最近几个版本都是由你破解的，完全服了！
超级支持！！！

dnawujun 发表于 2011-3-25 22:03

explain to us why only one file in folder win64, not whether it is a mistake?
owennnn 发表于 2011-3-25 18:27 http://bbs.simol.cn/images/common/back.gif

This is not a mistake,in 64 dll folder,the cedprot.dll is useless,you can try if you delete
this file ,the flux still can run(with 64 bit mode)
The cedprot.dll in 32bit folder is required by the old circuit editor,2D solver and Post

owennnn 发表于 2011-3-25 22:42

Thanks, now I understand
I will try later
Doing a great thing for the common good,
Now everyone has the opportunity to study ....

lijo 发表于 2011-3-25 23:30

本帖最后由 lijo 于 2011-3-26 04:17 编辑

SuperThanks DNAWUJUN.

Someone tried if working the Flux Simulink link into 64-bit ?

Anyone have the new documentation and examples ?

owennnn 发表于 2011-3-26 00:43

Without documentation and examples of badly{:1_443:}

infinity123 发表于 2011-3-26 10:31

can someoane post a hotfile link?

owennnn 发表于 2011-3-26 22:55

Question on installing v10.4 on WinXP SP3 x86

I did the following:
1. Installed the program
2. replaced electriflux, postpro2d, solver2d to oldest v.10.3
3. applied medicine dnawujun (replacement cedprot.dll and flux_project.dll from folder dll \ win32)
4. Start the program and got an error-"Preflu2d-soft run abort"
Flux3d: soft run abort ", etc.

The question is what did I do wrong ?????

owennnn 发表于 2011-3-26 23:02

On the x64 not yet tested.....
Who has the other results, share information{:1_443:}

dnawujun 发表于 2011-3-26 23:21

本帖最后由 dnawujun 于 2011-3-26 23:28 编辑

On the x64 not yet tested.....
Who has the other results, share information
owennnn 发表于 2011-3-26 23:02 http://bbs.simol.cn/images/common/back.gif

why you should replace the electriflux, postpro2d, solver2d to oldest v.10.3?
It no need to do that with the medicine
By the way , you should use this version
http://bbs.simol.cn/thread-65329-1-1.html
with this medicine

owennnn 发表于 2011-3-27 00:41

Thanks for the reply
Perhaps this is due to my wrong interpretation ....
Yes, I installed setupWinFlux10.4.rar
Then "The cedprot.dll in 32bit folder is required by the old circuit editor, 2D solver and Post" ... and further


I did so: back in place electriflux, postpro2d, solver2d of installation v.10.4.1

and still ERROR!
win32_cedprot.dll = CRC32 EF311CB9
win32_flux_project.dll = CRC32 5802C730
win64_flux_project.dll = CRC32 DDB1AEED

Maybe my hands are the curves?{:aa10

S_Z 发表于 2011-3-27 18:26

MotorSolve我也好期待啊谁要是能把软件发上来按楼主这实力我们就有望了！

owennnn 发表于 2011-3-27 19:10

My problem is solved
Installing on another machine has not caused any problems
{:1_390:}

jckstop 发表于 2011-3-27 20:15

要价太高，用不起啊，谁给共享一份，或者在qq群里啊
页: [1] 2 3 4 5
查看完整版本: 发个好东西给大家分享，信的就下