3D电磁感应，U型初级线圈，次级为何线圈无电压？

lwx_004 · 发表于 2011-9-10 10:50

马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。

您需要登录才可以下载或查看，没有账号？立即注册

x

所见模型，网格，云图，磁感应线如图所示~
但是结果无电压。

lwx_004 · 发表于 2011-9-10 10:51

EL= 26370  INDEPENDENT VOLTAGE SOURCE                CIRCU124  KOPT(1)= 4
  NODES       = 4534 4535 4536
  VOLTAGE SOURCE =  50.000    (Volt) (real)
  VOLTAGE       =  50.000    (Volt) (real)
  CURRENT       =-0.24797E-01 (Ampere)  (real)
  POWER (ABSORP) =-0.61992    (Watt) (real)    (output if negative)

EL= 26371  STRANDED COIL CURRENT SOURCE                CIRCU124  KOPT(1)= 5
  NODES       = 4534 4535    775
  SCAL          =  1.0000
  VOLTAGE       =  50.000    (Volt) (real)
  CURRENT       = 0.24797E-01 (Ampere)  (real)
  POWER (LOSSES) = 0.61992    (Watt) (real)

EL= 26372  INDEPENDENT VOLTAGE SOURCE                CIRCU124  KOPT(1)= 4
  NODES       = 4539 4540 4541
  VOLTAGE SOURCE =  50.000    (Volt) (real)
  VOLTAGE       =  50.000    (Volt) (real)
  CURRENT       =-0.25754E-01 (Ampere)  (real)
  POWER (ABSORP) =-0.64385    (Watt) (real)    (output if negative)

EL= 26373  STRANDED COIL CURRENT SOURCE                CIRCU124  KOPT(1)= 5
  NODES       = 4539 4540    858
  SCAL          =  1.0000
  VOLTAGE       =  50.000    (Volt) (real)
  CURRENT       = 0.25754E-01 (Ampere)  (real)
  POWER (LOSSES) = 0.64385    (Watt) (real)

EL= 26374  RESISTOR                                  CIRCU124  KOPT(1)= 0
  NODES       = 4544 4545
  RES          =  1000.0    (Ohm)
  VOLTAGE       =  0.0000    (Volt) (real)
  CURRENT       =  0.0000    (Ampere)  (real)
  POWER (ABSORP) =  0.0000    (Watt) (real)    (output if negative)

EL= 26375  STRANDED COIL CURRENT SOURCE                CIRCU124  KOPT(1)= 5
  NODES       = 4544 4545 1066
  SCAL          =  1.0000
  VOLTAGE       =  0.0000    (Volt) (real)
  CURRENT       =  0.0000    (Ampere)  (real)
  POWER (ABSORP) =  0.0000    (Watt) (real)    (output if negative)

lwx_004 · 发表于 2011-9-10 10:52

初级电压电流正常，次级无电压。。不知道原因，急求高手帮忙解决下~~~~不胜感谢。。。

lwx_004 · 发表于 2011-9-10 10:56

这个是模型命令流，最后没加边界平行条件和谐波分析方法和频率。请高手帮忙看看哪里出错了？

lwx_004 · 发表于 2011-9-11 09:46

怎么没人帮帮我额~~~~~

		自动登录	找回密码
密码			立即注册

[求助] 3D电磁感应，U型初级线圈，次级为何线圈无电压？

马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。

相关帖子