听说ansoft14里面有bug，是什么bug？我现在还没发现

20061964

在14里面听说有很严重的bug。是什么地方有bug？我目前试着用了一下，还没发现那里有

20061964

找到了，原来是静态场中非线性铁磁材料的设置上的bug。感谢西莫，翻帖子时无意中找到了

goodluck209

找到了，原来是静态场中非线性铁磁材料的设置上的bug。感谢西莫，翻帖子时无意中找到了
20061964 发表于 2011-5-3 15:13

                               
登录/注册后可看大图

    能把链接地址给下吗？

S_Z

不止是这些吧   有N个！   官方正版已经更新到  14.0.2

forlink

不止是这些吧   有N个！   官方正版已经更新到  14.0.2
S_Z 发表于 2011-5-3 19:57

                               
登录/注册后可看大图

请问，你是如何知道更新到14.0.2了呢？谢谢告知。

20061964

回复 3# goodluck209


    这个，真不好意思。我是今天上午看的帖子上说的这个，现在忘了在哪里了

20061964

回复 4# S_Z


    能说一下都有什么bug吗？我是现在只发现这一个。求告知

gajiter

ANSft00111909 - In Maxwell 14.0 the 3D magnetostatic solver was
failing on 32-bit versions of Windows when solving models with
nonlinear materials.

ANSft00112661 and ANSft00113127 - In 3D Transient models with
stranded windings, applying insulating boundaries to the outside
faces of the windings could cause incorrect, non-uniform current
density in some cases.

ANSft00111335 - In Maxwell 14.0 3D Magnetostatic and 3D Transient
models with anisotropic nonlinear materials would not solve.

ANSft00109025 - Edge force density values from Maxwell2D are now
correct for edges of moving parts for 2D transient designs with
motion. [However, the visualization of the force vectors in
Maxwell's fields post processor shows the direction of the vectors
without transforming with respect to the rotation and shows the
correct direction only in the initial position.]

ANSft00092048 - In Maxwell2D it is possible to use a translational
motion model with matching boundaries to emulate a wedge of a
rotating machine with very large radius (compared to the width
of the section being modeled). There was a bug leading to
incorrect results for some of these types of models.

ANSft00100030 - Maxwell 2D models with nonlinear materials in
which the BH curve extended into the 3rd quadrant would not
solve.

ANSft0011193 - The single-phase transformer model for Simplorer
created from a parametric solution in Maxwell was not correct
and would not work in Simplorer.



Bugs fixed in Maxwell 14.0.2
============================

ANSft00115800 - There was a bug in the meshmaker that could
cause failures when using the 'classic' mesher to make 3D meshes.
This bug existed on all platforms, but only seemed to cause a
failure on Linux versions.

US28128 - There was a file handle leak in the COM engines that
could cause an eventual COM engine failure in very large parametric
sweeps using DSO.

ANSft00114756 - In RMxprt, recording and playing back scripts that
set the 'End Ring conductor Type' would not work.

goodluck209

ANSft00111909 - In Maxwell 14.0 the 3D magnetostatic solver was
failing on 32-bit versions of Windo ...
gajiter 发表于 2011-7-3 22:35

                               
登录/注册后可看大图

    请问你有这些bug的补丁吗？谢谢

puff

有修正的补丁么？

huaxianzi

我的2d的静磁场仿真正常，但参数化的仿真不能计算torque等参数……有这样的吗？

gajiter

我启动更新检测，官方的自动升级升级到14.0.2，然后li错误，再重新破解一次，进入的菜单还是14.0，在软件的内部就变成14.0.2了

如果解决你的问题请务必回帖确认！！！！

gajiter

我的更新结果

xiangzi84

数据优化也有BUG，
跟实际单次计算出来的数据对不上！

阿牛2005

我的更新结果
gajiter 发表于 2011-7-4 22:53

                               
登录/注册后可看大图

谢谢。按照你的方法我也更新到14.0.2了。重新破解下可以使用，至于BUG因为我暂时没用到哪些功能，不能验证。

fanbei

我也  更新下   谢谢了

zptonghua

回复 16# fanbei


    这种方法可行否，还望认证后给下答案

cc87527

回复 12# gajiter


    我现在更新之后也出现li错误，请问是如何解决的。再PJ一次是如何操作的？
谢谢~

angelhellfallen

我的pj版的ansoft14的webupdate报错显示：internal error：webupdate is missing required information。无法更新。
请问是pj的问题吗？如何修正？

7279061

回复 19# angelhellfallen


    出现这个问题会影响软件运行吗？