11版本做的工程在16版本里打开报错，这是咋回事？

飞飞猪

11版本做的工程在16版本里打开报错，部分组件的材料消失了，如下图。请问这是咋回事呢？

飞飞猪

  MaxwellDesign1 (Magnetostatic)
    [warning] New ids are assigned to some faces/edges/vertices. Please run validation check and verify the integrity of all assignments before continuing. (8:21:26 上午  十二月 30, 2013)
  [warning] Unable to identify certain faces/edges/vertices of part SRMCore1. These entities are created by CreateUserDefinedPart operation. (8:21:26 上午  十二月 30, 2013)
  [warning] Unable to identify certain faces/edges/vertices of part SRMCore1. These entities are created by Subtract operation. (8:21:26 上午  十二月 30, 2013)
  [warning] Unable to identify certain faces/edges/vertices of part SRMCore1. These entities are created by Rotate operation. (8:21:26 上午  十二月 30, 2013)
  [warning] Unable to identify certain faces/edges/vertices of part SRMCore1. These entities are created by Rotate operation. (8:21:26 上午  十二月 30, 2013)
  [error] Separate operation failed due to lump count inconsistancy. Found 1 lumps instead of expected 9 lumps. (8:21:26 上午  十二月 30, 2013)
  [error] Error in retaining legacy geometry IDs. Please run validation check and verify the integrity of all assignments before continuing. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_1 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_2 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_3 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_4 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_5 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_6 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_7 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part SRMCore1_8 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part Section1 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)
  [error] Body could not be created for part Section2 because of invalid parameters of this part or some of its parent part/coordinate system. (8:21:26 上午  十二月 30, 2013)

这是错误信息！

luomu

估计16版本对一些命令做了修改，实在不行，就在16版本中重新建一个模型吧。

hamdizhang

看提示档应该是两个版本在你的文件里不兼容，是吧，周哥？{:soso_e113:}

飞飞猪

hamdizhang 发表于 2013-12-30 12:41
看提示档应该是两个版本在你的文件里不兼容，是吧，周哥？

您是哪位啊？{:soso_e132:}

飞飞猪

luomu 发表于 2013-12-30 09:39
估计16版本对一些命令做了修改，实在不行，就在16版本中重新建一个模型吧。

建模比较麻烦，请问您有啥好方法吗？

飞飞猪

问题已解决了！

starlover

楼主是咋解决的 告诉下大家呗

飞飞猪

starlover 发表于 2014-1-2 13:05
楼主是咋解决的 告诉下大家呗

我在16版本里又重新建模了！{:soso_e113:}

starlover

飞飞猪 发表于 2014-1-2 20:33
我在16版本里又重新建模了！

哈哈 原来如此

cjnk

我也出现这个问题，重新建模了还是有问题