solid117 input data 求问

imgose

SOLID97 Input Summary Nodes I, J, K, L, M, N, O, P
Degrees of Freedom See KEYOPT(1)
Real Constants None if KEYOPT(1) = 0 and KEYOPT(2) = 0.
For KEYOPT(1) = 2, 3, 5, or 6, and KEYOPT(2) = 0:
CARE, TURN, VOLU, DIRX, DIRY, DIRZ,  
CSYM, FILL  For KEYOPT(1) = 4 and KEYOPT(2) = 0:
CARE - Coil cross-sectional area  
For KEYOPT(1) = 0 or 1 and KEYOPT(2) = 1:
(blank), (blank), (blank), (blank), (blank), (blank),  
(blank), (blank), VELOX, VELOY, VELOZ, OMEGAX,  
OMEGAY OMEGAZ, XLOC, YLOC, ZLOC  
See Table 97.2: SOLID97 Real Constants for a description of the real constants.
Material Properties MUZERO, MURX, MURY, MURZ, RSVX, RSVY, RSVZ, MGXX, MGYY, MGZZ plus BH data table (see Material Data Tables (Implicit Analysis))
Surface Loads Maxwell Force Flags -- face 1 (J-I-L-K), face 2 (I-J-N-M), face 3 (J-K-O-N),  
face 4 (K-L-P-O), face 5 (L-I-M-P), face 6 (M-N-O-P)  
Magnetic-Circuit Interface Flags, if KEYOPT(1) = 4:
face 1 (J-I-L-K), face 2 (I-J-N-M), face 3 (J-K-O-N),  
face 4 (K-L-P-O), face 5 (L-I-M-P), face 6 (M-N-O-P)  

Body Loads Temperatures -- T(I), T(J), T(K), T(L), T(M), T(N), T(O), T(P)
MVDI -- VD(I), VD(J), VD(K), VD(L), VD(M), VD(N),  
VD(O), VD(P)  
Source Current Density, if KEYOPT(1) = 0 or 1 (See "SOLID97 Assumptions and Restrictions" for solenoidal restriction) -- JSX(I), JSY(I), JSZ(I), PHASE(I), JSX(J), JSY(J), JSZ(J), PHASE(J), JSX(K), JSY(K), JSZ(K), PHASE(K),  
JSX(L), JSY(L), JSZ(L), PHASE(L), JSX(M), JSY(M), JSZ(M), PHASE(M), JSX(N), JSY(N), JSZ(N), PHASE(N),  
JSX(O), JSY(O), JSZ(O), PHASE(O), JSX(P), JSY(P), JSZ(P), PHASE(P)  
Voltage Loading, if KEYOPT(1) = 2 -- VLTG(I), PHASE(I), VLTG(J), PHASE(J), VLTG(K), PHASE(K), VLTG(L), PHASE(L),  
VLTG(M), PHASE(M), VLTG(N), PHASE(N), VLTG(O), PHASE(O), VLTG(P), PHASE(P)  



    这是solid97的输入参数，红色部分是不是说明绞线圈要求其感抗和阻抗只能施加电压激励源？我要是施加电流或电流密度的话感抗和阻抗是无法求解的...谢谢！

cqlyj2008

回复 1# imgose
你是用什么求电感的，我见书上也没有说一定要电压激励的才能求电感啊

imgose

回复 2# cqlyj2008


    用ETABLE，8/9求阿，还有其他方法求么，那个LMATRIX宏命令貌似只能用静态分析时求解，我想求不同频率下线圈的感抗和阻抗...你有什么好办法，求教了...

cqlyj2008

回复 3# imgose
ETABLE可以求载压和载流线圈的电阻和电感啊。但是只能用于单线圈系统，线性，没有永磁铁的分析啊。