<?xml version="1.0" encoding="utf-8"?>
<rss version="2.0">
  <channel>
    <title>西莫电机圈 - 〖机电、电力电子与机电一体化〗</title>
    <link>https://bbs.simol.cn/forum-296-1.html</link>
    <description>Latest 20 threads of 〖机电、电力电子与机电一体化〗</description>
    <copyright>Copyright(C) 西莫电机圈</copyright>
    <generator>Discuz! Board by Comsenz Inc.</generator>
    <lastBuildDate>Tue, 14 Jul 2026 21:43:28 +0000</lastBuildDate>
    <ttl>60</ttl>
    <image>
      <url>https://bbs.simol.cn/static/image/common/logo_88_31.gif</url>
      <title>西莫电机圈</title>
      <link>https://bbs.simol.cn/</link>
    </image>
    <item>
      <title>径向磁悬浮轴承</title>
      <link>https://bbs.simol.cn/thread-218628-1-1.html</link>
      <description><![CDATA[实际情况：径向磁轴承线圈，在未接通电源的情况下，测量每组线圈的电感为5mH；
仿真情况：径向磁轴承线圈，在maxwell静磁场仿真中，在0电流的情况下，其电感量为44mH。
两者的模型尺寸一致、线圈匝数一致，想问问还有什么原因会导致这种情况？抑或是电磁仿真中设置有误 ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>idssa</author>
      <pubDate>Wed, 03 Dec 2025 08:12:06 +0000</pubDate>
    </item>
    <item>
      <title>输出转矩偏大是什么原因？</title>
      <link>https://bbs.simol.cn/thread-218565-1-1.html</link>
      <description><![CDATA[求问各位大神，空载反电势是正常的，齿槽转矩偏小一点，但加上电流之后输出转矩偏大，输出转矩应该是19Nm的，现在是29Nm，可能是什么原因造成的？]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>张豆</author>
      <pubDate>Wed, 26 Nov 2025 01:39:32 +0000</pubDate>
    </item>
    <item>
      <title>有刷电机仿真时报错</title>
      <link>https://bbs.simol.cn/thread-218335-1-1.html</link>
      <description><![CDATA[选的Universal Motors类型的电机，也设置了定子和转子，总是报while parsing expression: \&quot;-nan(ind)\&quot; an error was found near character 9, -nan(ind) is not a defined variable name in this context的类似错误，报一堆都是以-nan(ind)开头的，


选的General DC， ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>snowyang</author>
      <pubDate>Thu, 30 Oct 2025 08:44:25 +0000</pubDate>
    </item>
    <item>
      <title>磁通反向电机反电动势波形异常</title>
      <link>https://bbs.simol.cn/thread-218232-1-1.html</link>
      <description><![CDATA[磁通反向电机反电动势波形刚开始三项不对称，但后续又会对称，这是什么原因？]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>12345789</author>
      <pubDate>Mon, 13 Oct 2025 11:35:59 +0000</pubDate>
    </item>
    <item>
      <title>永磁同步电机maxwell仿真相电流激励和实际相电流的区别</title>
      <link>https://bbs.simol.cn/thread-218203-1-1.html</link>
      <description><![CDATA[在读书的时候做电磁仿真，仿真我都是选择的电流激励。表达式一般为Ipmax*sin(w*t+theta)，Ipmax为相电流的幅值。
设电机的输入功率为Pin，Pin=3*Up*Ip*cosφ，Up、Ip分别为相电压的有效值还有相电流的有效值，cosφ为功率因数。同时有Ipmax=sqrt(2)*Ip。当然用电流激励 ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>CMEE_RedA</author>
      <pubDate>Thu, 09 Oct 2025 03:19:09 +0000</pubDate>
    </item>
    <item>
      <title>Simplorer变流器+Maxwell电机联合仿真问题</title>
      <link>https://bbs.simol.cn/thread-218083-1-1.html</link>
      <description><![CDATA[Simplorer变流器和Maxwell电机联合仿真，将V_ROB1模块设置成电机额定转速 4100rpm，通过 MotionSetup1_in引脚接到电机有限元模型中，并把MotionSetupl_out引脚接地，完成对电机运动条件的设置。
仿真结果：电机三相电流达不到稳定是什么原因？按照列车牵引系统组成建立 ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>ssssss10</author>
      <pubDate>Tue, 16 Sep 2025 07:50:01 +0000</pubDate>
    </item>
    <item>
      <title>关于ANSYS EM2023R1版后，设计双馈发电机转子齿磁密计算问题</title>
      <link>https://bbs.simol.cn/thread-217592-1-1.html</link>
      <description><![CDATA[在ANSYS EM2023R1版后，更新的版本因内核改写，导致双馈发电机转子齿磁密与老版本计算相差太大，导致磁路计算和其他计算出现偏差，期待大虾解决]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>tztcl001</author>
      <pubDate>Tue, 01 Jul 2025 00:12:12 +0000</pubDate>
    </item>
    <item>
      <title>无铁芯轴向磁通电机，有一相反电动势高于其他两相</title>
      <link>https://bbs.simol.cn/thread-217571-1-1.html</link>
      <description><![CDATA[定子小了会出现很明显的趋势，定子大的成正弦变化]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>demo111</author>
      <pubDate>Fri, 27 Jun 2025 02:10:19 +0000</pubDate>
    </item>
    <item>
      <title>请问一下ANSYS EM2025R1版中的绕线转子模块计算结果不输出开路电压了吗？</title>
      <link>https://bbs.simol.cn/thread-217565-1-1.html</link>
      <description><![CDATA[如题，请教一下大伙，最新的ANSYS EM2025R1版中Rmxprt单元里面进行绕线转子三相异步电动机数据输入及计算后，计算结果里面不输出开路电压的数值了吗？]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>dream-ttt</author>
      <pubDate>Thu, 26 Jun 2025 08:11:27 +0000</pubDate>
    </item>
    <item>
      <title>maxwell 2d力分析求助</title>
      <link>https://bbs.simol.cn/thread-217523-1-1.html</link>
      <description><![CDATA[请问一下大佬们，我使用ansys maxwell在XY平面进行2d电磁分析，我对平面内的物体添加parameter进行电磁力分析的时候，发现得出的结果是这样的：x方向受到的力为393N,y方向受到的力为900N，请问一下结果中的力是这个物体在Z方向（即深度方向上）每米受到的力吗？ ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>scz</author>
      <pubDate>Wed, 18 Jun 2025 13:43:52 +0000</pubDate>
    </item>
    <item>
      <title>窗口显示不完全</title>
      <link>https://bbs.simol.cn/thread-217493-1-1.html</link>
      <description><![CDATA[有大佬遇到过这种情况吗？Maxwell中某些窗口显示不完全，请问怎么解决]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>擎天柱</author>
      <pubDate>Sun, 15 Jun 2025 08:40:17 +0000</pubDate>
    </item>
    <item>
      <title>直线电机仿真问题求助</title>
      <link>https://bbs.simol.cn/thread-217442-1-1.html</link>
      <description><![CDATA[大家好，我在仿真圆筒直线电机时遇到了一个问题，静磁场和瞬态场磁力线走向不一样，瞬态场磁力线是乱的，而且还出现了不成回路的情况。]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>yang12345</author>
      <pubDate>Sun, 08 Jun 2025 12:51:43 +0000</pubDate>
    </item>
    <item>
      <title>在Maxwell里如何仿真转速-转矩曲线？</title>
      <link>https://bbs.simol.cn/thread-217441-1-1.html</link>
      <description><![CDATA[想问一下永磁同步电机，想在Maxwell里仿真不同工况（从额定工况到峰值工况电流不同）下的转速-转矩曲线，应该如何操作呀，是参数化扫描，还是说用ACT的tollkit？]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>NanXun</author>
      <pubDate>Sun, 08 Jun 2025 12:31:10 +0000</pubDate>
    </item>
    <item>
      <title>maxwell仿真2D永磁电机损耗</title>
      <link>https://bbs.simol.cn/thread-217419-1-1.html</link>
      <description><![CDATA[电机仿真为什么导进去的这个永磁体的热量是0w，Maxwell里面材料设置的也没问题，也选了涡流损耗了]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>十月的梦</author>
      <pubDate>Thu, 05 Jun 2025 02:57:32 +0000</pubDate>
    </item>
    <item>
      <title>永磁同步电机设计问题！求助！！</title>
      <link>https://bbs.simol.cn/thread-217248-1-1.html</link>
      <description><![CDATA[最近小弟在学电磁设计，关于额定电压和电机供电电压产生疑问。
问题1：比如电机额定电压为380V，控制方式为SVPWM，经过逆变器后，实际最大输入线电压交流有效值为356.59V，也就是说根据公式P=根号3UIcos求出的电机线电压应该不超过356.59这个值是吧；
问题2：在Maxwell ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>lililiz</author>
      <pubDate>Mon, 12 May 2025 03:21:16 +0000</pubDate>
    </item>
    <item>
      <title>12槽8极和24槽8极永磁电机性能区别</title>
      <link>https://bbs.simol.cn/thread-217159-1-1.html</link>
      <description><![CDATA[最近按照数据3kw，3000rpm，9.5nm数据，下线了两个电机定子，一个按照12槽8极下线，一个按照24槽8极下线，分别安装到同一个转子上，打算看看两者之间性能的差别，刚开始，两个电机表现出来的外特性差不多，但是扭矩上升到7.2nm的时候，24槽8极电机正常，12槽8极电机失速 ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>沐风雨</author>
      <pubDate>Wed, 30 Apr 2025 07:40:24 +0000</pubDate>
    </item>
    <item>
      <title>无刷双馈发电机仿真</title>
      <link>https://bbs.simol.cn/thread-217065-1-1.html</link>
      <description><![CDATA[想请问一下为什么我这个无刷双馈发电机仿真出来的PW绕组电压波形一直像下图一样重复，绕组和外电路查过都没问题]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>sjsaj</author>
      <pubDate>Sat, 19 Apr 2025 07:19:35 +0000</pubDate>
    </item>
    <item>
      <title>关于ansysmaxwell2024中2D仿真求永磁同步电机中各相电感</title>
      <link>https://bbs.simol.cn/thread-217063-1-1.html</link>
      <description><![CDATA[哪位大佬遇到过这种情况，具体如下面：
   我把电机的一个实际模型进行测绘后，在ansysmaxwell2024中建立有限元2D模型，仿真，如下图，参数设置应该都是正确的，因为仿真过后得到的转矩输出和反电动势以及各种电压和实测中是一致的，我想在仿真中看电机在各种电流下的电 ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>lhm520116</author>
      <pubDate>Fri, 18 Apr 2025 16:38:36 +0000</pubDate>
    </item>
    <item>
      <title>联合仿真问题</title>
      <link>https://bbs.simol.cn/thread-216927-1-1.html</link>
      <description><![CDATA[求问联合仿真跑到2s的时候就停下是为什么？
simplorer中的信息如下：
[Sim2000App]
        Info - Simulation stopped by user.
        &gt;&gt;        Calculate at t=2 s
matlab的报错信息入下：
错误: S-Function \'AnsoftSFunction\' 报告错误:
Error Synchronizing with ...]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>刘姥姥</author>
      <pubDate>Wed, 02 Apr 2025 07:29:52 +0000</pubDate>
    </item>
    <item>
      <title>motor cad里短路电流问题</title>
      <link>https://bbs.simol.cn/thread-216885-1-1.html</link>
      <description><![CDATA[请教一下，motorcad里的短路电流仿真

1.为什么我跑完短路电流以后，最大去磁电流与我给定的峰值电流基本一致？]]></description>
      <category>〖机电、电力电子与机电一体化〗</category>
      <author>lee727</author>
      <pubDate>Wed, 26 Mar 2025 04:47:06 +0000</pubDate>
    </item>
  </channel>
</rss>