band与master\slave的矛盾问题
本帖最后由 zdyulu 于 2010-12-4 18:29 编辑/4的电机瞬态分析模型学习中，提示错误！
Could not map middle points on the moving mesh band.Possible causes are: 1) Motion setup is not correct. 2) The model uses rotational motion, the geometry is less than a full circle, and master-slave boundaries were not defined on the surfaces of the wedge. 3) The model uses translational motion, and true surface curves were used on the band object or on the outermost faces of moving objects. 4) Extremely small gaps or faces exist in the geometry. These may need to be removed or enlarged.
在使用软件自带的 Region，没有设置master、slave时，执行没有错误提示，可自己设置画出了一个Region，并设置了master、slave时，执行就提示错误。 大哥，都搞3D了呀，小弟佩服，我现在2D都还没搞明白哦！学习中！ 运动设置的translational motion？这个不对吧 本帖最后由 zdyulu 于 2010-12-6 11:16 编辑
请教3楼兄弟:我的模型是1/4的，该如何设置呀？？我对band和region进行了重新设置。可问题又有了提示错误如下：
“Mesh Operation”采用了系统默认值，自己未进行设计。提示错误如下：
The band surface is represented with too few segments. The maximum angle per segment is 15 degrees. Simulation completed with execution error on server: Local Machine. (10:26 上午十二月 06, 2010)
在对”Number of segment”重新设置逐渐增大从30～600，提示不变。没法了就对“Mesh Operation”采用了自己设计，提示错误又变为下边：
Seeding mesh, process mesh3d_ng : Error in matching boundary process. (10:39 上午十二月 06, 2010)
Simulation completed with execution error on server: Local Machine. (10:39 上午十二月 06, 2010) maxwell的3D技术文档《Study of a Permanent Magnet Motor with MAXWELL 3D:Example of the 2004 Prius IPM Motor》中采用的对band的分数是每一度一份。楼主可以试试。还有我刚学maxwell的时候，跟着这个文档做，也遇到楼主的那个问题。“/4的电机瞬态分析模型学习中，提示错误！
Could not map middle points on the moving mesh band.Possible causes are: 1) Motion setup is not correct. 2) The model uses rotational motion, the geometry is less than a full circle, and master-slave boundaries were not defined on the surfaces of the wedge. 3) The model uses translational motion, and true surface curves were used on the band object or on the outermost faces of moving objects. 4) Extremely small gaps or faces exist in the geometry. These may need to be removed or enlarged.
”
后来就花了一早上重头画一遍图，后来就没错了。我建议楼主看看文章，跟着文档里面的步骤来。一定可以
谢谢！我一定
按照例题做做！ 我也正头疼这个问题，试试吧，希望能解决 我也遇到了这个问题，我的是整个模型，不用设边界，yc_dd17 回复 4# zdyulu
瞬态求解，必须手动部分，需注意的是BAND地方部分比其它地方稍密些 恩，很感激。在探索中。。。 我也遇到这个问题 maxwell的3D技术文档《Study of a Permanent Magnet Motor with MAXWELL 3D:Example of the 2004 Prius IPM ...
hangang0214 发表于 2010-12-7 10:55 http://bbs.simol.cn/images/common/back.gif
怎麼分了兩部份啊？ 谢谢五楼的资料，受益匪浅 band 一直出现“The band surface is represented with too few segments. The maximum angle per segment is 15 degrees.”求解决啊
hangang0214 发表于 2010-12-7 10:55 static/image/common/back.gif
maxwell的3D技术文档《Study of a Permanent Magnet Motor with MAXWELL 3D:Example of the 2004 Prius IPM ...
谢谢楼主分享资料 谢谢楼上的分享资料！！！ 大哥，我做3D计算的时候我也遇到你一模一样的错误，你的是怎么解决的呢？ 同上怎么解决啊
谢谢楼上的分享资料！！！ 谢谢分享，添加主从边界时也遇到问题，有没有分析轴向磁密电机的？
页:
[1]
2