利用RMxprt做出来的永磁电机2D模型仿真，气隙磁密波形非常的差
附件是电机模型 看一下磁力线和磁密云图 磁密怎么全是正的 检查一下RMxprt的计算结果，是否本身也有问题 因为取得是绝对值，而不是径向磁密，别问怎么弄，论坛搜索下 drger 发表于 2017-12-1 08:43检查一下RMxprt的计算结果，是否本身也有问题
ADJUSTABLE-SPEED PERMANENT MAGNET SYNCHRONOUS MOTOR DESIGN
File: Setup1.res
GENERAL DATA
Rated Output Power (kW): 16
Rated Voltage (V): 380
Number of Poles: 4
Frequency (Hz): 50
Frictional Loss (W): 50
Windage Loss (W): 0
Rotor Position: Inner
Type of Circuit: Y3
Type of Source: Sine
Domain: Time
Operating Temperature (C): 75
STATOR DATA
Number of Stator Slots: 36
Outer Diameter of Stator (mm): 210
Inner Diameter of Stator (mm): 150
Type of Stator Slot: 3
Stator Slot
hs0 (mm): 0.15
hs1 (mm): 0.25
hs2 (mm): 13
bs0 (mm): 3.5
bs1 (mm): 5
bs2 (mm): 9
rs (mm): 2.5
Top Tooth Width (mm): 8.15855
Bottom Tooth Width (mm): 6.43982
Skew Width (Number of Slots): 0
Length of Stator Core (mm): 100
Stacking Factor of Stator Core: 0.95
Type of Steel: D23_50
Designed Wedge Thickness (mm): 0.250018
Slot Insulation Thickness (mm): 0
Layer Insulation Thickness (mm): 0
End Length Adjustment (mm): 0
Number of Parallel Branches: 1
Number of Conductors per Slot: 60
Type of Coils: 21
Average Coil Pitch: 7
Number of Wires per Conductor: 1
Wire Diameter (mm): 0.8
Wire Wrap Thickness (mm): 0.06
Slot Area (mm^2): 112.405
Net Slot Area (mm^2): 110.817
Limited Slot Fill Factor (%): 75
Stator Slot Fill Factor (%): 40.0443
Coil Half-Turn Length (mm): 225.526
Wire Resistivity (ohm.mm^2/m): 0.0217
ROTOR DATA
Minimum Air Gap (mm): 0.7
Inner Diameter (mm): 35
Length of Rotor (mm): 100
Stacking Factor of Iron Core: 0.95
Type of Steel: D23_50
Bridge (mm): 0.5
Rib (mm): 2
Mechanical Pole Embrace: 0.95
Electrical Pole Embrace: 0.956771
Max. Thickness of Magnet (mm): 6
Width of Magnet (mm): 85
Type of Magnet: XG196/96
Type of Rotor: 5
Magnetic Shaft: No
PERMANENT MAGNET DATA
Residual Flux Density (Tesla): 0.96
Coercive Force (kA/m): 690
Maximum Energy Density (kJ/m^3): 183
Relative Recoil Permeability: 1
Demagnetized Flux Density (Tesla): 0.166361
Recoil Residual Flux Density (Tesla): 0.913527
Recoil Coercive Force (kA/m): 726.983
MATERIAL CONSUMPTION
Armature Wire Density (kg/m^3): 8900
Permanent Magnet Density (kg/m^3): 7800
Armature Core Steel Density (kg/m^3): 7820
Rotor Core Steel Density (kg/m^3): 7820
Armature Copper Weight (kg): 2.17927
Permanent Magnet Weight (kg): 1.5912
Armature Core Steel Weight (kg): 9.5968
Rotor Core Steel Weight (kg): 10.4235
Total Net Weight (kg): 23.7908
Armature Core Steel Consumption (kg): 20.5765
Rotor Core Steel Consumption (kg): 13.1281
STEADY STATE PARAMETERS
Stator Winding Factor: 0.901912
D-Axis Reactive Reactance Xad (ohm): 31.9406
Q-Axis Reactive Reactance Xaq (ohm): 166.539
D-Axis Reactance X1+Xad (ohm): 34.5998
Q-Axis Reactance X1+Xaq (ohm): 169.198
Armature Leakage Reactance X1 (ohm): 2.65916
Zero-Sequence Reactance X0 (ohm): 1.87854
Armature Phase Resistance R1 (ohm): 7.01001
Armature Phase Resistance at 20C (ohm): 5.7663
NO-LOAD MAGNETIC DATA
Stator-Teeth Flux Density (Tesla): 1.15781
Stator-Yoke Flux Density (Tesla): 2.18887
Rotor-Yoke Flux Density (Tesla): 0.575476
Air-Gap Flux Density (Tesla): 0.54733
Magnet Flux Density (Tesla): 0.77313
Stator-Teeth By-Pass Factor: 0.0006686
Stator-Yoke By-Pass Factor: 0.00368971
Rotor-Yoke By-Pass Factor: 1.97551e-005
Stator-Teeth Ampere Turns (A.T): 8.16588
Stator-Yoke Ampere Turns (A.T): 288.914
Rotor-Yoke Ampere Turns (A.T): 4.23128
Air-Gap Ampere Turns (A.T): 368.37
Magnet Ampere Turns (A.T): -670.365
Leakage-Flux Factor: 1.04056
Correction Factor for Magnetic
Circuit Length of Stator Yoke: 0.0851935
Correction Factor for Magnetic
Circuit Length of Rotor Yoke: 0.683379
No-Load Line Current (A): 5.19863
No-Load Input Power (W): 699.52
Cogging Torque (N.m): 2.14306
FULL-LOAD DATA
Note:
This motor cannot offer the given rated output power.
The following results are of the maximum output.
Maximum Line Induced Voltage (V): 939.162
Root-Mean-Square Line Current (A): 12.5893
Root-Mean-Square Phase Current (A): 12.5893
Armature Thermal Load (A^2/mm^3): 1445.24
Specific Electric Loading (A/mm): 57.7041
Armature Current Density (A/mm^2): 25.0457
Frictional and Windage Loss (W): 50
Iron-Core Loss (W): 81.1261
Armature Copper Loss (W): 3333.01
Total Loss (W): 3464.14
Output Power (W): 4843.03
Input Power (W): 8307.17
Efficiency (%): 58.2994
Synchronous Speed (rpm): 1500
Rated Torque (N.m): 30.8317
Torque Angle (degree): 93
Maximum Output Power (W): 4843.03
Torque Constant KT (Nm/A): 0.748461
WINDING ARRANGEMENT
The 3-phase, 2-layer winding can be arranged in 9 slots as below:
AAAZZZBBB
Angle per slot (elec. degrees): 20
Phase-A axis (elec. degrees): 90
First slot center (elec. degrees): 0
TRANSIENT FEA INPUT DATA
For Armature Winding:
Number of Turns: 360
Parallel Branches: 1
Terminal Resistance (ohm): 7.01001
End Leakage Inductance (H): 0.00240323
2D Equivalent Value:
Equivalent Model Depth (mm): 100
Equivalent Stator Stacking Factor: 0.95
Equivalent Rotor Stacking Factor: 0.95
Equivalent Br (Tesla): 0.913527
Equivalent Hc (kA/m): 726.983
Estimated Rotor Inertial Moment (kg m^2): 0.0373396
等待的沉默 发表于 2017-12-1 09:44
ADJUSTABLE-SPEED PERMANENT MAGNET SYNCHRONOUS MOTOR DESIGN
File: Setup1.r ...
帮忙看下设计报告 存在什么问题
页:
[1]